滑牙要買哪種工具解決 - 3C

By Lucy
at 2022-05-09T15:20

Table of Contents

如題
最近有需要拆過保電供然後這電供不知道螺絲是怎樣有夠爛
http://i.imgur.com/nXnXDxc.jpg

超級大崩牙沒救了
橡皮筋跟電火布都沒救就算了還越轉越崩
慘

後來放棄這些偏方想直接用崩牙工具解決
上海鮮商城看到有幾種有螺紋的什麼的
但好像都是適合大螺絲跟水管那種的
想請問一下這種0.5cm寬的崩牙用哪種工具解決比較好
http://i.imgur.com/aaxBXLz.jpg

因為只是對付爛螺絲大概只想花個兩三百不知道這預算有沒有適合的工具

-----
更新:已經先買0號退牙器了應該是可以用在5mm螺絲上大概花200
再不行就去找電鑽了
也謝謝大家提供的其他解法

-----
Sent from JPTT on my OPPO CPH2023.

--

Tags: 3C

All Comments

By Ivy
at 2022-05-11T15:02

直接買新的

By Jack
at 2022-05-10T00:24

直接電鑽鑽穿阿

By Kelly
at 2022-05-12T00:06

用電磨鑽出一個一字凹槽，然用一字
起子退出來，屢試不爽

By Hamiltion
at 2022-05-10T00:24

家家不是都有鐵鎚嗎???

By Heather
at 2022-05-12T00:06

有點焊機焊個螺絲轉下來

By Harry
at 2022-05-10T00:24

點焊機+1

By Ina
at 2022-05-12T00:06

我覺得能解決的方法都不划算XD

By Erin
at 2022-05-10T00:24

焊一個螺絲上去不錯好像可以試試看

By Gilbert
at 2022-05-12T00:06

如果有角磨機+切金屬直接切斷螺絲

By Jessica
at 2022-05-10T00:24

https://i.imgur.com/C9k6NM4.jpg

By Sandy
at 2022-05-12T00:06

鋸條插進去慢慢磨斷也可以

By Noah
at 2022-05-10T00:24

買新的啊還問

By Ivy
at 2022-05-12T00:06

買鑽金屬的鑽尾就可以了

By Eartha
at 2022-05-10T00:24

逆絲攻直接轉

By Victoria
at 2022-05-12T00:06

磨個一字痕最快，不然就拿去鐵工廠
焊個T字鐵轉出來！

By George
at 2022-05-10T00:24

這算除錯文嗎

By Genevieve
at 2022-05-12T00:06

類除錯

By Donna
at 2022-05-10T00:24

要治崩牙的請買日貨ANEX 真D猛

By Thomas
at 2022-05-12T00:06

怎感覺像是鉚釘…

By Jacky
at 2022-05-10T00:24

這麼小的很難逆出來，直接電鑽幹掉

By Tracy
at 2022-05-12T00:06

已經被你轉到沒肉能讓工具咬住了

By Eden
at 2022-05-10T00:24

熱熔膠

By Rebecca
at 2022-05-12T00:06

我是覺得直接換新電供比較省事，反
正都過保了。

By Sarah
at 2022-05-10T00:24

套筒螺絲

By Jacky
at 2022-05-12T00:06

你搞成這樣可能直接鑽孔打出新基
座比較快那個孔應該沒救了

By Lily
at 2022-05-10T00:24

相信我左右鑽一點用一字轉起來就
好了

By Ivy
at 2022-05-12T00:06

瓦數不大的話其實買新電供會比你
搞那些成本低

By Jacob
at 2022-05-10T00:24

應該是機殼和電供有公差吧

By Poppy
at 2022-05-12T00:06

問買哪種工具聰明

By Catherine
at 2022-05-10T00:24

手機近拍很強，且有柔光

By Andy
at 2022-05-12T00:06

暴龍鉗！！

By Victoria
at 2022-05-10T00:24

熱熔膠試試看

By Wallis
at 2022-05-12T00:06

買鋸子鋸開來

By Hedda
at 2022-05-10T00:24

直接拿去搪缸店，秒殺

By Kristin
at 2022-05-12T00:06

用橡皮筋增加摩擦力應該就行了

By Eartha
at 2022-05-10T00:24

啊，沒看到橡皮筋orz

By Belly
at 2022-05-12T00:06

你這個退牙器沒用，用電鑽

By Catherine
at 2022-05-10T00:24

問就是買新的電供

By Hedwig
at 2022-05-12T00:06

解決的方法很多只是大部分你都沒工

By Zora
at 2022-05-10T00:24

具機可以使用

By Kelly
at 2022-05-12T00:06

你用電動去轉的？

By Necoo
at 2022-05-10T00:24

熱融膠

By Robert
at 2022-05-12T00:06

類除錯XDD

By James
at 2022-05-10T00:24

電鑽鑽掉就好，如果一顆可能是螺絲
問題，四顆絕對是你的問題，多學學
鎖螺絲再DIY吧

By Rachel
at 2022-05-12T00:06

拿電工用的扁頭尖嘴鉗，夾著螺絲頭
轉起來就好。

By Rae
at 2022-05-10T00:24

崩牙只要有頭露在外面的都能這樣轉

By Jacky
at 2022-05-12T00:06

暴龍鉗有防靜電的好用

By Andy
at 2022-05-10T00:24

不過你這個太嚴重了，暴龍鉗應該沒
用

By Oscar
at 2022-05-12T00:06

斜口鉗慢慢轉啊

By Daniel
at 2022-05-10T00:24

大概設計理念就是不給你拆一拆就壞

By Bennie
at 2022-05-12T00:06

用最小號的退牙器#0可以試試

By Agnes
at 2022-05-10T00:24

電鑽 /快乾 /切一個I字一字轉下去

By Jacob
at 2022-05-12T00:06

斜口鉗看能不能插進螺絲縫裡轉開

By Victoria
at 2022-05-10T00:24

如果你有電動工具其實都好解決但
問題是你沒有所以相對來說可能買
新的在成本上面會比較適合

By George
at 2022-05-12T00:06

如果只是為了這次就買了一堆一次性
工具那實在沒必要

By Zanna
at 2022-05-10T00:24

攻牙專用工具+電鑽

By David
at 2022-05-12T00:06

下次轉要拿鐵鎚敲一下螺絲比較好轉

By Franklin
at 2022-05-10T00:24

這種電鑽了

By Oscar
at 2022-05-12T00:06

斜口鉗，咬住，轉～～

By Heather
at 2022-05-10T00:24

沒工具的話其實蠻麻煩的
光買工具的錢可能可以直接買新的

By Edith
at 2022-05-12T00:06

我看我同事用榔頭敲一字起，硬敲出
凹痕。

By Aaliyah
at 2022-05-10T00:24

退牙器通常是裝在電動工具（起子機
或電鑽）上使用的銑刀端開孔螺旋
端退牙低轉速逆轉 YT上很多教學可
以先看一下

By Michael
at 2022-05-12T00:06

沒有電動工具你找的那個退牙器也沒
辦法用手動退牙工具暴龍鉗那家公司
有出一組不過不便宜

By Hardy
at 2022-05-10T00:24

手夠力就鉗子夾住轉或者把螺絲頭夾

By Madame
at 2022-05-12T00:06

掉

By Thomas
at 2022-05-10T00:24

先說你轉到滑牙先看看你的螺絲起子
是不是有問題使用不正確的號數

By Hardy
at 2022-05-12T00:06

小螺絲超的超難解

By Madame
at 2022-05-10T00:24

沒肉逆紋救不了

By Oscar
at 2022-05-12T00:06

買新的省時省力

By Iris
at 2022-05-10T00:24

搜尋螺絲滑牙救星看水電專業的來

By Ethan
at 2022-05-12T00:06

刻磨機刻出一字凹痕，再用一字起子
鬆開

By Yedda
at 2022-05-10T00:24

電鑽有在DIY的早晚會買

By Olivia
at 2022-05-12T00:06

沒有什麼問題是C4不能解決的
如果有，那就兩顆！

By Todd Johnson
at 2022-05-10T00:24

暴龍鉗！

By Hazel
at 2022-05-12T00:06

你這個直接鑽掉比較省事

By Delia
at 2022-05-10T00:24

https://i.imgur.com/hCcbo7N.jpg

By Aaliyah
at 2022-05-12T00:06

來這裡就是買新的

By Harry
at 2022-05-10T00:24

找東西點快乾

By Lydia
at 2022-05-12T00:06

這等級的螺絲都是那種很軟沒熱處理
過的，手動鑽就能挖掉

By Leila
at 2022-05-10T00:24

點好點準

By James
at 2022-05-12T00:06

用魚線卡住就轉出來了

By Leila
at 2022-05-10T00:24

淘寶兩百多的電鑽就能處理了

By Joe
at 2022-05-12T00:06

是男人都應該要有把電鑽不論好跟壞

By Daph Bay
at 2022-05-10T00:24

一字起

By Adele
at 2022-05-12T00:06

...這個已經不只是滑牙了，兄ㄉㄟ
ˇ～

By Thomas
at 2022-05-10T00:24

不管怎麼樣，總之我很震驚，大力出
奇蹟？

By Yedda
at 2022-05-12T00:06

刻個凹痕用一字起轉

By Yedda
at 2022-05-10T00:24

發現轉不動就該拿虎鉗來轉了

By Una
at 2022-05-12T00:06

直接鑽洞啦

By Damian
at 2022-05-10T00:24

慘

By Brianna
at 2022-05-12T00:06

笑死你是怎麼搞的能滑成這樣

By Yedda
at 2022-05-10T00:24

在用小的螺絲鑽孔

By Faithe
at 2022-05-12T00:06

1.鑽孔再用反牙螺絲轉出來 2.砂輪
機鋸一條線再用一字起子

By Faithe
at 2022-05-10T00:24

拿的起子頭尺寸不對硬轉才會這樣吧

By Madame
at 2022-05-12T00:06

兄day 你的牙都不見了XD
直接用鑽頭鑽暴最快

By Bennie
at 2022-05-10T00:24

買新的

By Emily
at 2022-05-12T00:06

點焊，轉出奶

By Daph Bay
at 2022-05-10T00:24

居家必備:電鑽

By Hedwig
at 2022-05-12T00:06

五金行老闆問看看有一種電動鑽有
機會卡住並且咬下來

By Delia
at 2022-05-10T00:24

弄成這樣應該是用電動起子然後沒壓
緊就轉吧？

By Ingrid
at 2022-05-12T00:06

很軟？一字敲下去直接轉就好了，除
非他直接斷牙給你看...

By Adele
at 2022-05-10T00:24

我拿烙鐵直接滴焊錫在螺絲上趁還沒
冷卻插個小一字起字進去當模具冷

By Delia
at 2022-05-12T00:06

卻後成功把筆電散熱器的崩牙螺絲轉
出來XD

By Susan
at 2022-05-10T00:24

樓上這方法神發想啊。

By Ursula
at 2022-05-12T00:06

星字批頭配T霸敲下去就可以了

By Una
at 2022-05-10T00:24

比起一字兩刻，星字六刻抓力比較夠

By Ingrid
at 2022-05-12T00:06

震動槍？

By Victoria
at 2022-05-10T00:24

快乾或AB膠

By Carolina Franco
at 2022-05-12T00:06

電源供應器那薄薄的鐵皮外殼經得起
敲？

By Emma
at 2022-05-10T00:24

打鑰匙的鎖匠店處理牙崩這種專業
的

By Hamiltion
at 2022-05-12T00:06

不想買電動工具就買手鑽啊這麼軟

By Oliver
at 2022-05-10T00:24

其實電動起子都能慢速定速轉吧

By Donna
at 2022-05-12T00:06

用usb充電的那種
手動感覺力道更不穩

By Edwina
at 2022-05-10T00:24

暴龍鉗

By Vanessa
at 2022-05-12T00:06

買新的

By Kelly
at 2022-05-10T00:24

唯一推薦電鑽

By Bennie
at 2022-05-12T00:06

敲或磨成一字啊

滑牙要買哪種工具解決 - 3C

All Comments

Related Posts

慎選SAMSUNG ODYSSEY G5 32"曲面螢幕

雙塔空冷 SCYTHE 風魔2疾風版簡單測試

CPU散熱器問題

請問2000mbps以上的路由器是給誰用的?

intel驅動下載問題