請問Bios的蜂鳴聲 - 電腦

※ 引述《popoloo (波波羅o)》之銘言：
: ※ 引述《Ellomorce ( ＋Bentham =)》之銘言：
: : 想問一下Award Bios
: : 不斷地響　　　　　　電源,顯示器未和顯示卡連接好
: : 重覆短響　　　　　　電源有問題
: : 這兩者到底有什麼差別啊??
: : 我最近每逢週二電腦就固定掛掉
: : 所有東西都正常運作就只差沒畫面
: : 開機要嘛什麼聲音都沒有
: : 要嘛就是發出很急促的連續短響
: : 我自己懷疑是顯示卡的問題
: : 因為往往去上個課或睡個覺之後又好了
: : 但是我認不清那個響聲到底是上面的那一個
: 可以檢查ram..
: 我覺得網路上的FAQ好像都寫錯了
: 因為上次ram沒插好
: 就是一直短響
: 害我以為是power問題~"~
: 拿了別台power還是一樣
: 後來把ram重插才好
: 所以一直短響的訊息應該是ram沒插好
: 但是不知道為什麼網路上的資料都是"電源問題"
: 該不會轉來轉去錯的就變對的了吧~"~?

見P兄這樣說，我就隨手去google找了相關網頁 (關鍵字 BIOS BEEP)
底下所列的資料擷取自下列網頁，
大致看了一下與網路上流傳的BIOS錯誤碼應無二致 (我真的只是大致看一下喔 XP)
http://www.pcguide.com/ts/x/sys/beep/
有點多，但是常用的就是AMI跟AWARD(還請高手告知在下，它是啥時被併掉的呀?)
PHOENIX的還有依訊息聲響數不同的兩個版本，有興趣的就看一下吧。
*在此處AWARD的訊息只能顯示VGA與RAM的錯誤判定。

[AMI]
1 Beep: DRAM refresh failure
2 Beeps: Parity circuit failure
3 Beeps: Base 64K RAM failure
4 Beeps: System timer failure
5 Beeps: Processor failure
6 Beeps: Keyboard controller / gate A20 failure
7 Beeps: Virtual mode exception error
8 Beeps: Display memory read/write failure
9 Beeps: ROM BIOS checksum failure
10 Beeps: CMOS shutdown register read/write error
11 Beeps: Cache memory error
Continuous Beeping: Memory or video problem
Other Beep Codes

[AWARD]
1 Long Beep: Memory problem
1 Long, then 2 Short Beeps: Video error
1 Long, then 3 Short Beeps: Video error
Continuous Beeping: Memory or video problem
Other Beep Codes

[PHOENIX]
Older BIOS Family (Phoenix BIOS Plus, PhoenixBIOS 1.x)
1-1-3 (02h): CMOS write/read test failure
1-1-4 (03h): BIOS ROM checksum failure
1-2-1 (04h): Programmable interval timer test failure
1-2-2 (05h): DMA initialization failure
1-2-3 (06h): DMA page register write/read test failure
1-3-1 (08h): RAM refresh verification failure
1-3-3 (0Ah): 1st 64K RAM chip or data line failure - multi-bit
1-3-4 (0Bh): 1st 64K RAM odd/even logic failure
1-4-1 (0Ch): 1st 64K RAM address line failure
1-4-2 (0Dh): 1st 64K RAM parity test in progress or failure
2-1-1 (10h): 1st 64K RAM chip or data line failure - bit 0
2-1-2 (11h): 1st 64K RAM chip or data line failure - bit 1
2-1-3 (12h): 1st 64K RAM chip or data line failure - bit 2
2-1-4 (13h): 1st 64K RAM chip or data line failure - bit 3
2-2-1 (14h): 1st 64K RAM chip or data line failure - bit 4
2-2-2 (15h): 1st 64K RAM chip or data line failure - bit 5
2-2-3 (16h): 1st 64K RAM chip or data line failure - bit 6
2-2-4 (17h): 1st 64K RAM chip or data line failure - bit 7
2-3-1 (18h): 1st 64K RAM chip or data line failure - bit 8
2-3-2 (19h): 1st 64K RAM chip or data line failure - bit 9
2-3-3 (1Ah): 1st 64K RAM chip or data line failure - bit A
2-3-4 (1Bh): 1st 64K RAM chip or data line failure - bit B
2-4-1 (1Ch): 1st 64K RAM chip or data line failure - bit C
2-4-2 (1Dh): 1st 64K RAM chip or data line failure - bit D
2-4-3 (1Eh): 1st 64K RAM chip or data line failure - bit E
2-4-4 (1Fh): 1st 64K RAM chip or data line failure - bit F
3-1-1 (20h): Master DMA register test failure
3-1-2 (21h): Slave DMA register test failure
3-1-3 (22h): Master interrupt mask register test failure
3-1-4 (23h): Slave interrupt mask register test failure
3-2-4 (27h): Keyboard controller test failure
3-3-4 (2Bh): Screen memory test failure
3-4-1 (2Ch): Screen initialization failure
3-4-2 (2Dh): Screen retrace test failure
4-2-1 (34h): Timer tick interrupt test failure
4-2-2 (35h): Shutdown test failure
4-2-3 (36h): Gate A20 failure
4-2-4 (37h): Unexpected interrupt in protected mode
4-3-1 (38h): RAM test failure above address 0FFFFh
4-3-3 (3Ah): Interval timer channel 2 test failure
4-3-4 (3Bh): Time-Of-Day clock test failure
4-4-1 (3Ch): Serial port test failure
4-4-2 (3Dh): Parallel port test failure
4-4-3 (3Eh): Math coprocessor test failure

Newer BIOS Family (PhoenixBIOS 4.x)
1-1-1-3 (02h): Verify real mode
1-1-2-1 (04h): Get CPU type
1-1-2-3 (06h): Initialize system hardware
1-1-3-1 (08h): Initialize chipset registers with initial POST values
1-1-3-2 (09h): Set in POST flag
1-1-3-3 (0Ah): Initialize CPU registers
1-1-4-1 (0Ch): Initialize cache to initial POST values
1-1-4-3 (0Eh): Initialize I/O
1-2-1-1 (10h): Initialize Power Management
1-2-1-2 (11h): Load alternate registers with initial POST values
1-2-1-3 (12h): Jump to UserPatch0
1-2-2-1 (14h): Initialize keyboard controller
1-2-2-3 (16h): BIOS ROM checksum
1-2-3-1 (18h): 8254 timer initialization
1-2-3-3 (1Ah): 8237 DMA controller initialization
1-2-4-1 (1Ch): Reset Programmable Interrupt Controller
1-3-1-1 (20h): Test DRAM refresh
1-3-1-3 (22h): Test 8742 Keyboard Controller
1-3-2-1 (24h): Set ES segment register to 4 GB
1-3-3-1 (28h): Autosize DRAM
1-3-3-3 (2Ah): Clear 512K base RAM
1-3-4-1 (2Ch): Test 512 base address lines
1-3-4-3 (2Eh): Test 512K base memory
1-4-1-3 (32h): Test CPU bus-clock frequency
1-4-2-1 (34h): CMOS RAM read/write failure
1-4-2-4 (37h): Reinitialize the chipset
1-4-3-1 (38h): Shadow system BIOS ROM
1-4-3-2 (39h): Reinitialize the cache
1-4-3-3 (3Ah): Autosize cache
1-4-4-1 (3Ch): Configure advanced chipset registers
1-4-4-2 (3Dh): Load alternate registers with CMOS values
2-1-1-1 (40h): Set Initial CPU speed
2-1-1-3 (42h): Initialize interrupt vectors
2-1-2-1 (44h): Initialize BIOS interrupts
2-1-2-3 (46h): Check ROM copyright notice
2-1-2-4 (47h): Initialize manager for PCI Options ROMs
2-1-3-1 (48h): Check video configuration against CMOS
2-1-3-2 (49h): Initialize PCI bus and devices
2-1-3-3 (4Ah): Initialize all video adapters in system
2-1-4-1 (4Ch): Shadow video BIOS ROM
2-1-4-3 (4Eh): Display copyright notice
2-2-1-1 (50h): Display CPU type and speed
2-2-1-3 (52h): Test keyboard
2-2-2-1 (54h): Set key click if enabled
2-2-2-3 (56h): Enable keyboard
2-2-3-1 (58h): Test for unexpected interrupts
2-2-3-3 (5Ah): Display prompt "Press F2 to enter SETUP"
2-2-4-1 (5Ch): Test RAM between 512 and 640k
2-3-1-1 (60h): Test expanded memory
2-3-1-3 (62h): Test extended memory address lines
2-3-2-1 (64h): Jump to UserPatch1
2-3-2-3 (66h): Configure advanced cache registers
2-3-3-1 (68h): Enable external and CPU caches
2-3-3-2 (69h): Initialize SMI handler
2-3-3-3 (6Ah): Display external cache size
2-3-4-1 (6Ch): Display shadow message
2-3-4-3 (6Eh): Display non-disposable segments
2-4-1-1 (70h): Display error messages
2-4-1-3 (72h): Check for configuration errors
2-4-2-1 (74h): Test real-time clock
2-4-2-3 (76h): Check for keyboard errors
2-4-4-1 (7Ch): Set up hardware interrupts vectors
2-4-4-3 (7Eh): Test coprocessor if present
3-1-1-1 (80h): Disable onboard I/O ports
3-1-1-3 (82h): Detect and install external RS232 ports
3-1-2-1 (84h): Detect and install external parallel ports
3-1-2-3 (86h): Re-initialize onboard I/O ports
3-1-3-1 (88h): Initialize BIOS data area
3-1-3-3 (8Ah): Initialize extended BIOS data area
3-1-4-1 (8Ch): Initialize floppy controller
3-2-1-1 (90h): Initialize hard-disk controller
3-2-1-2 (91h): Initialize local-bus hard-disk controller
3-2-1-3 (92h): Jump to UserPatch2
3-2-2-1 (94h): Disable A20 address line
3-2-2-3 (96h): Clear huge ES segment register
3-2-3-1 (98h): Search for option ROMs
3-2-3-3 (9Ah): Shadow option ROMs
3-2-4-1 (9Ch): Set up Power Management
3-2-4-3 (9Eh): Enable hardware interrupts
3-3-1-1 (A0h): Set time of day
3-3-1-3 (A2h): Check key lock
3-3-3-1 (A8h): Erase F2 prompt
3-3-3-3 (AAh): Scan for F2 key stroke
3-3-4-1 (ACh): Enter SETUP
3-3-4-3 (AEh): Clear in-POST flag
3-4-1-1 (B0h): Check for errors
3-4-1-3 (B2h): POST done--prepare to boot operating system
3-4-2-1 (B4h): One beep
3-4-2-3 (B6h): Check password (optional)
3-4-3-1 (B8h): Clear global descriptor table
3-4-4-1 (BCh): Clear parity checkers
3-4-4-3 (BEh): Clear screen (optional)
3-4-4-4 (BFh): Check virus and backup reminders
4-1-1-1 (C0h): Try to boot with INT 19
4-2-1-1 (D0h): Interrupt handler error
4-2-1-3 (D2h): Unknown interrupt error
4-2-2-1 (D4h): Pending interrupt error
4-2-2-3 (D6h): Initialize option ROM error
4-2-3-1 (D8h): Shutdown error
4-2-3-3 (DAh): Extended Block Move
4-2-4-1 (DCh): Shutdown error
4-2-4-3 (DEh): Keyboard Controller Failure
4-3-1-3 (E2h): Initialize the chipset
4-3-1-4 (E3h): Initialize refresh counter
4-3-2-1 (E4h): Check for Forced Flash
4-3-2-2 (E5h): Check HW status of ROM
4-3-2-3 (E6h): BIOS ROM is OK
4-3-2-4 (E7h): Do a complete RAM test
4-3-3-1 (E8h): Do OEM initialization
4-3-3-2 (E9h): Initialize interrupt controller
4-3-3-3 (EAh): Read in bootstrap code
4-3-3-4 (EBh): Initialize all vectors
4-3-4-1 (ECh): Boot the Flash program
4-3-4-2 (EDh): Initialize the boot device
4-3-4-3 (EEh): Boot code was read OK

--